| 滚筒的工具使用和保养 |
| 添加时间：2019/7/23 14:42:21 浏览次数： |
| 滚筒的工具使用和保养 Use and Maintenance of Roller Tools 1.施工工具短毛滚筒在不用时，应泡在材料内不让它接触空气，否则滚筒会硬化，无法继续使用。每天工作完成时，一定要把滚筒彻底的洗净。同时轴处要特别注意不要被材料粘死，否则滚筒不能很好地转动，无法理想地施工。 1. When the short wool drum of construction tools is not in use, it should be soaked in the material and not let it touch the air, otherwise the drum will harden and can not continue to use. When the work is finished every day, the drum must be thoroughly washed. At the same time, special attention should be paid to the shaft not to be stuck by the material, otherwise the drum can not rotate well and can not be ideally constructed. 2.涂布要领：手和肩尽量不用力，以小指、无名指、中指握住滚筒柄，再加上食指，以拇指从上轻按，使滚筒垂直涂面，轻轻滚转。遵守先上后下，先左后右，先边角后大面的原则。调整涂料含量，轻轻抵着涂面由下而上，由上而下反复分配涂料，然后使滚筒上下笔直旋转。滚筒的回转速度太快时，涂料的飞溅太多，要慢慢移动。 2. Coating essentials: hand and shoulder as little as possible, with little finger, ring finger, middle finger to grasp the drum handle, plus index finger, thumb from the top gently press, so that the drum vertical coating, gently roll. Follow the principle of top-down, left-first, right-first, corner-first and large-sided. Adjust the paint content, gently against the coating surface from bottom to top, from top to bottom repeatedly distribute paint, and then make the drum up and down straight rotation. When the rotating speed of the drum is too fast, the paint splashes too much, so it needs to move slowly. 3：料板上调节涂料的含量，使其含着涂料不流坠的程度。涂布大约是滚筒长度3-4倍范围内较轻的接触将涂料涂布在被涂物上。涂面时起初用较轻的力量逐渐加力使涂料均匀的涂出。 3: Material board to adjust the content of paint, so that it contains the degree of paint does not fall. Coating is about 3 - 4 times the length of the drum in the range of lighter contact coating on the coating. At first, the paint is evenly coated with a lighter force. 4、若一次涂过于广大的面积，则涂膜交合处会形成滚筒痕，故要使滚筒宽度的三分之一重叠，以50-60CM2为基准进行涂装，狭窄处于小滚筒。施工大墙面时，同时以分层分段的按分格每层的分格缝来施工，先用胶纸做好的分格缝上下的保护措施，涂布时，用竹杆加长滚筒，由每层最高处一次性滚到每层的最低处。 4. If the coating area is too large at one time, the drum mark will be formed at the junction of the coating film. Therefore, to make one third of the drum width overlap, coating is carried out on the basis of 50-60CM2, and the narrowness is in the small drum. During the construction of large wall, the construction is carried out by layered and segmented grid joints of each layer. First, the protective measures for the upper and lower grid joints are done with glue paper. When coating, the roller is lengthened by bamboo pole, and rolled from the highest part of each layer to the lowest part of each layer at one time. 5、喷涂时离开施工墙面30厘米左右，自上而下或自左至右均匀喷涂。施工过程中，必须不定时地清理喷枪喷嘴，以确保施工质量。 5. When spraying, leave the construction wall about 30 centimeters and spray evenly from top to bottom or from left to right. In order to ensure the quality of construction, the nozzles of spray guns must be cleaned from time to time during construction. |
| 上一页 传动滚筒制动失灵原因 |
| 下一页 传动滚筒保养方法 |